John Deere 8100 Specs ( 1995-1999 )
Production
| Description | Row-Crop tractor / Built in Waterloo, Iowa, USA |
|---|---|
| Manufacturer | John Deere |
Engine
| Engine type | John Deere 7.6L 6-cyl diesel |
|---|---|
| Air cleaner | dual paper elements with aspirator |
| Bore/Stroke | 4.5625x4.75 inches (116 x 121 mm) |
| Compression | 15.1:1 |
| Coolant capacity | 28.8 qts (27.3 L) |
| Description | John Deere / turbocharged diesel / 6-cylinder / liquid-cooled |
| Displacement | 466 ci (7.6 L) |
| Firing order | 1-5-3-6-2-4 |
| Oil capacity | 22.7 qts (21.5 L) |
| Rated RPM | 2200 |
| Starter volts | 12 |
| Drawbar (tested) | 141.81 hp (105.7 kW) |
| PTO (claimed) | 160 hp (119.3 kW) |
| PTO (tested) | 179.15 hp (133.6 kW) |
Transmission
| Clutch | hydraulic wet disc |
|---|---|
| Gears | 16 forward and 4 reverse |
| Oil capacity | 148 qts (140.1 L) |
| Transmission | John Deere PowerShift |
| Transmission type | 16-speed full power shift |
| Type | full power shift |
Mechanical
| Cab | CommandView Cab standard. Row-Trak guidance optional. |
|---|---|
| Description | Power steering / Differential hydraulic wet disc brakes |
| Differential lock | electro-hydraulic |
| Drive type | Two- or four-wheel drive |
| Final drives | inboard planetary |
Capacity
| Front diff. | 11.5 qts (10.9 L) |
|---|---|
| Front hubs | 3.2 qts (each) (3.0 L) |
| Fuel | 135 gal (511.0 L) |
| Hydraulic system | 37 gal (140.0 L) |
Hydraulics
| Capacity | 37 gal (140.0 L) |
|---|---|
| Pressure | 2900 psi (200.0 bar) |
| SCV flow | 30 gpm (113.6 lpm) |
| Type | closed center pressure-flow compensated (PFC) |
| Valves | 3 to 5 |
Hitch
| Control | electro-hydraulic draft sensing |
|---|---|
| Rear lift | 10400 lbs (4717 kg) |
| Rear Type | III/IIIN |
PTO
| Clutch | hydraulic wet disc |
|---|---|
| Engine RPM | 540@1930 |
| Rear PTO | independent |
| Rear PTO Type | 1000 (1.75) |
Electrical
| Batteries | 2 |
|---|---|
| Battery CCA | 925 |
| Battery volts | 12 |
| Charging amps | 140 |
| Charging system | alternator |
| Ground | negative |
Dimensions & Tires
| 2WD Front tread | 60 to 84 inches (152 to 213 cm) |
|---|---|
| 2WD Ground clearance | 31.5 inches (80 cm) |
| 2WD Wheelbase | 122.8 inches (311 cm) |
| 4WD Front tread | 60 to 88 inches (152 to 223 cm) |
| 4WD Ground clearance | 23.2 inches (58 cm) |
| 4WD Wheelbase | 116.1 inches (294 cm) |
| Height | 120.2 inches (305 cm) |
| Length | 206.5 inches (524 cm) |
| Optional large axle rear axle | 4.331 by 118.5 inches (110 by 3009 mm) |
| Optional short axle rear axle | 3.937 by 110.5 inches (99 by 2806 mm) |
| Standard axle rear axle | 3.937 by 118.5 inches (99 by 3009 mm) |
| 2WD Rear tire | 18.4R46 |
| 2WD Wheelbase | 122.8 inches (311 cm) |
| 4WD Wheelbase | 116.1 inches (294 cm) |
| Front tire | 11.00-24 |
| Weight | 16435 to 18914 pounds |
| 2WD Standard tires (ag) | Front: 11.00-24. Rear: 18.4R46 |
8100 Serial Number Location
| Description | Serial number plate on the rear of the tractor, above the PTO shaft. |
|---|
8100 Serial Numbers
| 1995 | 1001 |
|---|---|
| 1996 | 4001 |
| 1997 | 10001 |
| 1998 | 20001 |
| 1999 | 24001 |
| Description | FAQ: How to read a serial number table. |
John Deere 8100 Weight
| 2WD Shipping | 16435 lbs (7454 kg) |
|---|---|
| 4WD Shipping | 17876 lbs (8108 kg) |
| Operating | 18914 lbs (8579 kg) |
Nebraska Tractor Test 1688
| Description | PTO performance / Drawbar performance / Gear 8 used for power test. / Gear 3 used for pull test. |
|---|---|
| Fuel use | 9.7 gal/hour (36.7 l/hour) / 9.2 gal/hour (34.8 l/hour) / 9.1 gal/hour (34.4 l/hour) |
| Max power | 179.15 hp (133.6 kW) / 141.81 hp (105.7 kW) |
| Max pull | 21,586 lbs (9791 kg) |
| Power at rated engine speed | 160.40 hp (119.6 kW) |
| Transmission type | 16-speed 4WDApril 19 - May 15, 1995Link: Nebraska Tractor Test 1688 file |
References
| Description | New 8000 Series Tractors published in 1995, by John Deere / 8000 Series Tractors published in 1996, by John Deere / Operator's Manual 8100, 8200, 8300 and 8400 Tractors (OMAR113872) published in 1994 |
|---|